Antenna length calculator (dipole and quarter wave)

Type a frequency or pick a band to get dipole, quarter-wave and 5/8-wave lengths in metres or feet and inches.

0.95 for wire antennas. Pick a cable only when you cut coax or ladder line to an electrical length; check its data sheet.

Dipole total10.03 m
Each leg5.01 m
Quarter wave5.01 m
5/8 wave12.54 m
each leg 5.01 m total 10.03 mhalf-wave dipole 5.01 mquarter-wave vertical

    Trim helper

    How to use the antenna length calculator

    1. Type the frequency, or pick a band preset: the ham bands from 160 m to 70 cm, CB, FM, ADS-B and the 433, 868 and 915 MHz bands.
    2. Keep the velocity factor at 0.95 for a wire antenna, or pick a cable when you are cutting coax or ladder line.
    3. Choose Metres or Feet and inches, read the lengths and press Copy lengths. After a first SWR test, type the frequency of the lowest SWR in the Trim helper.

    Worked example: a 14.2 MHz dipole

    leg 5.01 m (16 ft 5.4 in)leg 5.01 m (16 ft 5.4 in) total 10.03 m (32 ft 10.8 in) at 14.2 MHz, factor 0.95 coax to the radio 468 ÷ 14.2 = 32.96 ft (10.05 m): the old rule agrees within 2 cm
    Each leg is a quarter wave times the velocity factor; together they make the half-wave dipole.

    Say you want a dipole for the middle of the 20 m band, 14.2 MHz. The free-space wavelength is 299.79 ÷ 14.2 = 21.11 m. Half of that is 10.56 m. A real wire antenna works out a little shorter than the free-space figure, so multiply by the 0.95 velocity factor: 10.03 m in total, or 5.01 m on each side of the feed point. In feet that is 32 ft 10.8 in in total and 16 ft 5.4 in per leg.

    The old rule of thumb, 468 ÷ frequency in MHz, gives 32.96 ft, which is 10.05 m: 2 cm longer, so it is the same antenna for any practical purpose. A quarter-wave vertical for 14.2 MHz is 5.01 m tall, and a 5/8-wave vertical 12.54 m. Cut the wire 2 to 5 % long, so each leg is 5.11 to 5.26 m, hang it, measure the SWR and trim.

    Use cases

    HF wire dipole

    For 40 m, a dipole cut for 7.1 MHz is 20.06 m in total, 10.03 m a side. Hang it as high as you can, keep the ends away from metal gutters, and feed it in the middle with 50 Ω coax through a 1:1 choke balun. If the garden only allows a sloping wire or an inverted V, start from the same lengths: the shape and height shift the resonance a little, and the trim helper tells you how much to change.

    2 m / 70 cm ground plane

    A quarter-wave ground plane for 145 MHz has a 49.1 cm vertical element and four radials of about the same length. Sloping the radials down at about 45° brings the feed impedance close to 50 Ω; flat radials give a lower one. For 70 cm (435 MHz) the vertical is 16.4 cm. A 5/8-wave vertical, 1.23 m on 2 m, sends more of its signal towards the horizon, but it needs a matching coil at the base.

    433 MHz module antenna

    Small 433.92 MHz transmitter and receiver modules often have a pad for the antenna and nothing attached. A straight wire of 16.4 cm, a quarter wave with the 0.95 factor, works far better than a random length, and a ground plane under it helps. The same rule gives 8.2 cm for 868 MHz and 7.8 cm for 915 MHz. After that, range depends on power, height and walls; the link budget calculator puts numbers on it.

    Why real antennas need trimming

    The formula assumes a thin wire far from everything. Real antennas sit near the ground, roofs and trees, often use insulated wire, which makes them resonate a few percent lower, and have end insulators and loops of wire that add length. Each of these moves the resonant frequency, so the first cut is a starting point. Measure the SWR at a few frequencies and find where it is lowest.

    Length and frequency go in opposite directions. If a dipole cut for 14.2 MHz shows its lowest SWR at 13.9 MHz, it is 2.1 % too long, so each 5.01 m leg comes down to 4.91 m. Trim both legs by the same amount, a little at a time. To see what an SWR reading means in return loss and lost power, check VSWR with the VSWR calculator.

    Formula

    Wavelength (m) = 299.79 ÷ frequency (MHz). Each length = wavelength × fraction × velocity factor: full wave × 1, half-wave dipole × 1/2 (each leg × 1/4), quarter wave × 1/4 and 5/8 wave × 5/8. With the 0.95 wire factor the whole dipole is 142.4 ÷ MHz metres, close to the 468 ÷ MHz feet rule. 1 ft = 0.3048 m and 1 in = 2.54 cm. Trimming: new length = length now × lowest-SWR frequency ÷ wanted frequency. All RF calculators are on the RF tools page.

    FAQ

    How long is a half-wave dipole?

    About 142.5 ÷ frequency in MHz metres in total (468 ÷ MHz in feet), half on each side.

    What is velocity factor?

    How much slower the wave travels along the wire than in free space; it makes the antenna a bit shorter.

    Should I cut the antenna exactly?

    Cut a little long, then trim while checking VSWR.

    How long is a quarter-wave for 433 MHz?

    About 16.5 cm. With the 0.95 wire factor the tool gives 16.4 cm for 433.92 MHz.

    Written and tested by the SpectrumAnalyzer.app team · Last checked

    How we tested: Checked by hand: 14.2 MHz with a 0.95 factor gives a 10.03 m dipole (32 ft 10.8 in), 5.01 m legs and a 12.54 m 5/8 wave; 433.92 MHz gives a 16.4 cm quarter wave; 145 MHz gives 49.1 cm.