Engine and motor RPM from sound

Hold your phone near an engine, motor or fan and read its RPM from the sound. Choose the type and count, and the maths is shown.

— RPM

— Hz 4-stroke engine, 4 cylinders: RPM = Hz × 120 ÷ 4

×1

Press Listen, or open a recording

Pick the engine type and the number of cylinders, poles or blades first. The browser asks to use your microphone; your sound stays on this device.

Or drop a file here.

Highest—
Median—
Steady—
Harmonics—

RPM range

Reading
Averaging
Long steadies a rough or noisy engine; Off follows fast revving best.

The tool finds the frequency with the strongest row of harmonics in the range. If the RPM reads double or half, press ÷2 or ×2. To pick a peak yourself, click it on the spectrum; Auto undoes that.

Source

Video files work when the browser can open their sound (mp4 and webm in most browsers). Files are read on this device only; they are never uploaded.

Export and share

The share link holds the settings only, never the sound.

Sound never leaves your device. Nothing is uploaded. Space listenH hold+ ×2− ÷2

How to use the RPM meter

  1. Choose the type: 4-stroke engine, 2-stroke engine, Electric motor, Fan or propeller, or Other. Then pick the number of cylinders, poles or blades.
  2. Press Listen and hold your phone 30 to 100 cm from the engine or fan, away from moving parts and hot exhaust. For a video or a recording, choose Audio or video file and open it.
  3. Read the RPM. The amber line on the spectrum shows the frequency used, and the chart below draws the RPM over time.
  4. If the number is double or half what you expect, press ÷2 or ×2. Press Hold to freeze the reading, and Save CSV to keep the readings.

No engine nearby?

How it turns sound into RPM

firing frequency 100 Hz 2×3×4×5×6× 100200300400500700 Hz 100 Hz × 120 ÷ 4 cylinders = 3,000 RPM
A 4-cylinder 4-stroke engine at 3,000 RPM fires 100 times a second, so its sound has a strong 100 Hz tone with harmonics above it.

An engine does not hum at one pitch by chance. Every time a cylinder fires, the exhaust and the block get a push, and those pushes repeat at a steady rate. That rate is the firing frequency, measured in hertz (pushes per second). The tool searches the spectrum for the frequency with the strongest row of evenly spaced harmonics, refines it from all the harmonics it finds, and turns it into RPM with the rule for your engine type:

TypePulses per turnRuleExample
4-stroke enginecylinders ÷ 2RPM = Hz × 120 ÷ cylinders4 cylinders at 100 Hz = 3,000 RPM
2-stroke enginecylindersRPM = Hz × 60 ÷ cylinders1 cylinder at 150 Hz = 9,000 RPM
Electric motorpoles ÷ 2RPM = Hz × 120 ÷ poles14 poles at 1,400 Hz = 12,000 RPM
Fan or propellerbladesRPM = Hz × 60 ÷ blades7 blades at 140 Hz = 1,200 RPM

A 4-stroke cylinder fires once every two turns of the crankshaft, which is where the 120 comes from. A 2-stroke fires every turn. For a motor, the pole count is the number of magnet poles; the electrical frequency of the windings is the RPM × poles ÷ 120. A fan or propeller makes one pressure pulse each time a blade passes, called the blade pass frequency.

The worked example: a 4-cylinder car engine idling at 750 RPM fires at 750 × 4 ÷ 120 = 25 Hz. At 3,000 RPM it is 100 Hz, and at 6,000 RPM 200 Hz. The spectrum chart shades the range searched, so you can see that the right peak is inside it.

Use cases

Small engines (mowers, mopeds)

A lawn mower or generator with a governor should hold a steady speed. Set 4-stroke and 1 cylinder, and a mower running at 3,000 RPM shows a strong tone at 25 Hz with harmonics at 50, 75 and 100 Hz. If the RPM wanders by more than a few percent while the load is steady, the Steady readout shows it, and the RPM chart shows the hunting as a wave. A moped with a single-cylinder 2-stroke at 6,000 RPM gives 100 Hz.

RC planes and drones

Propellers are loud and clean, which suits this tool. Set Fan or propeller and the blade count: a 2-blade prop at 12,000 RPM makes 400 Hz. Compare two props on the same motor and battery, or check that all motors of a drone run at the same speed by recording each one. For the motor itself, choose Electric motor with its pole count; a 14-pole motor at 12,000 RPM has an electrical frequency of 1,400 Hz, often heard as a whine.

PC and ceiling fans

A PC case fan with 7 blades at 1,200 RPM gives 140 Hz, so you can check what a fan really does at a given setting. A ceiling fan turns slowly: 5 blades at 180 RPM is only 15 Hz, which phone mics hear poorly, so hold the mic close in a quiet room. The hum of a mains-powered fan or motor usually follows the mains (100 or 120 Hz), not the speed.

Tips: check the harmonic with ×2 and ÷2

The most common mistake is a reading that is exactly double or half the real speed. An engine with uneven cylinders also makes "half orders" below the firing frequency, and some engines have a weak firing tone with a strong second harmonic. Check against something you know: the tachometer at idle, a rev limiter, or a typical idle speed. If the tool says 1,500 RPM where you expect 3,000, press ×2. The note under the chart also suggests ×2 when the odd harmonics of the reading are much weaker than the even ones.

  • Point the mic at the exhaust or intake from a safe distance, not at a loud fan belt.
  • Use Long averaging for a rough idle and Off for quick revs.
  • Narrow the RPM range to the speeds you expect, so the tool cannot pick a tone outside it.
  • Below about 10 Hz (a single-cylinder 4-stroke under 1,200 RPM) readings get unreliable.

To see every frequency in the sound, open the live spectrum analyzer. For keypad tones, use the DTMF decoder. All decoders are on the more signal decoders page.

FAQ

How can sound show RPM?

Each firing stroke or blade pass makes a pulse. Their rate is a frequency, and RPM follows from it.

How accurate is it?

Within a few percent when the right harmonic is picked. Use the ×2 and ÷2 buttons if it reads double or half.

Does it work for electric motors?

Yes. Enter the pole count, or use the blade count for fans.

Can it check engine vibration?

No. Vibration analysis needs a vibration sensor tool.

Written and tested by the SpectrumAnalyzer.app team · Last checked

How we tested: Checked with the site's own test file: an engine-like sound with a 100 Hz firing frequency and harmonics to 600 Hz reads 100.00 Hz, which is 3,000 RPM for a 4-cylinder 4-stroke (expected 3,000 RPM ±1 %).