Audio tests · Guide
How to fix mains hum and ground loop hum
A low, steady hum from your speakers is almost never a broken speaker. In most homes and studios it comes from the mains power, at 50 Hz or 60 Hz, sneaking into the audio cables through a ground loop. This guide shows you how to confirm it is hum, then how to fix it one safe step at a time.
Try it
Hold your phone or laptop near the speaker, or play a recording of the noise. The analyzer opens with the Mains hum preset and tells you if it finds 50 Hz or 60 Hz hum and its harmonics.
Hum or buzz? Read the pattern
Before you change any cables, find out what kind of noise you have. A spectrum analyzer shows it in a few seconds, because mains noise always sits at exact, fixed frequencies.
Hum is a deep, soft tone. On the analyzer it shows as one tall peak at the mains frequency (60 Hz in North America, 50 Hz in Europe, the UK, Africa, Australia and most of Asia), often with smaller peaks at 2, 3 and 4 times that frequency: 120, 180 and 240 Hz, or 100, 150 and 200 Hz. A ground loop usually makes this pattern.
Buzz is harsher and sounds a bit like an insect. On the analyzer it shows as a long comb of peaks, 60 or 50 Hz apart, that reaches well into the kilohertz. Buzz comes from sharp pulses of current, for example from a light dimmer, a cheap LED driver, a switch-mode power supply or a cable lying next to a power cable.
To measure it, press "Find hum now", hold the phone's microphone about 10 cm from the speaker cone with no music playing, and wait a few seconds. The preset uses a very fine frequency step (about 1.5 Hz per line) and a 20 Hz to 1 kHz view, so the peaks are easy to read. Write down the level of the tallest peak, for example "60 Hz at −48 dB". After each fix, measure again in the same spot. If the number falls by 20 dB, the hum is now ten times weaker and usually hard to hear.
Two more clues help. If the noise changes when you turn a volume knob, it enters before that knob, so look at the source and its cable. If it stays the same at any volume, it enters after the knob, at the amplifier or the speaker cables. And if the peak sits at an odd frequency such as 47 Hz or 15.7 kHz, it is not mains hum at all; see "When it is not hum" below.
Step-by-step fixes
Work through these steps in order, from the free ones to the ones that cost a little. Turn the volume down before you plug or unplug anything, and keep the analyzer open so you can see the hum peak drop instead of guessing by ear. A drop of 20 dB or more means you found the cause.
Unplug one cable at a time
Start with everything connected and the hum playing. Then unplug the audio cables one by one, starting with the one furthest from the speakers, and watch the 50 or 60 Hz peak each time. When the hum stops, the last cable you removed, or the device on the other end of it, is part of the loop.
Do not forget the cables that are not audio cables: a TV aerial or cable box line, a USB cable to a computer and an HDMI cable all carry a ground connection. A cable TV line is one of the most common hidden causes of hum in a home cinema.
One power strip
A ground loop forms when two devices reach earth through different paths, for example an amplifier plugged into one wall socket and a turntable or computer plugged into another socket across the room. The small voltage difference between those two earth points pushes a current along the shield of the audio cable, and you hear it as hum.
Plug every device in the audio chain into one good power strip, fed from one wall socket. This gives them all the same earth point and often removes the hum at once. Keep the strip away from big transformers, fridges and heaters.
Ground loop isolator
If one link still hums, for example a laptop or a car stereo connected with an RCA or 3.5 mm cable, a ground loop isolator is the quickest fix. It is a small box with a tiny transformer inside that passes the music but breaks the ground path between the two devices. You plug it into the cable that carries the hum, and nothing else changes.
A basic ground loop isolator for 3.5 mm or RCA cables is cheap and safe to use, because it never touches the mains earth. Cheap ones can soften the deepest bass a little, so check the result with music you know.
We may earn a commission if you buy through these links. It does not change the price.
Balanced cables
In a studio, the lasting fix is balanced connections: XLR or TRS (three-contact jack) cables between an audio interface or mixer and active speakers. A balanced cable carries the signal twice, once upside down, and the receiving device keeps only the difference between the two. Hum picked up along the way is the same on both wires, so it cancels out.
Balanced cables only help when both ends are balanced. A TRS cable into a plain RCA input works as an unbalanced cable again. Check the labels on your gear, or look for "balanced" in the manual.
Laptop on charger
A laptop that is silent on battery but hums when the charger is plugged in is a classic ground loop. The charger links the laptop to the mains, the audio cable links it to your amplifier, and the two paths close the loop. The noise often changes when you move the mouse or when the screen changes, because the laptop's own circuits add whine on top of the hum.
Try these in order: run on battery while you record or listen; plug the charger into the same power strip as the amp; use a charger with a three-pin (earthed) plug; or put a USB isolator or a ground loop isolator in the audio path. A USB audio interface powered from the same strip often solves it for good.
Dimmers and LED drivers
Light dimmers and cheap LED drivers switch the current on and off very quickly, 100 or 120 times a second. That makes a sharp buzz with many harmonics, which can get into guitar pickups, long unbalanced cables and nearby amplifiers. Turn the lights fully on or off and watch the analyzer: if the comb of peaks shrinks, the light is the cause.
Move audio cables away from light fittings and power cables, and cross power and audio cables at right angles instead of running them side by side. Replace the worst dimmer or LED driver with a better-quality one, and keep phone chargers and wall adapters away from guitar amps.
When it is not hum
Not every steady noise is mains hum. A noise that rises and falls with a computer's work is usually fan noise or coil whine: a high, thin whine from parts inside a graphics card or power supply, often between 2 and 15 kHz. It is not tied to 50 or 60 Hz, so the analyzer shows peaks at odd frequencies that move as the load changes.
An electric guitar with single-coil pickups also hums at 50 or 60 Hz, but that hum is picked up from the air, not from a ground loop. It changes as you turn your body or move closer to a computer screen or a light. Humbucking pickups, a noise gate or simply facing another way are the usual answers.
A soft "shhh" across all frequencies is hiss, from a gain control turned up too far. A peak that drifts slowly is often a fridge, fan or air conditioner in the room, which the microphone hears directly. A tick or click once a second is often a mobile phone near a cable. None of these are fixed by the ground loop steps above.
Safety: never remove earth pins
You may read online that cutting or taping over the earth pin of a plug, or using a "cheater" adapter, removes hum. It often does, and it is dangerous. The earth pin is what keeps the metal case of your amplifier safe if something inside fails. Without it, the case can become live, and the next person to touch it and another earthed device at the same time can get a serious shock.
Every fix on this page keeps the safety earth in place. If you still have hum after all of them, ask a qualified electrician to check the wiring of your sockets.
When the hum is gone, a quick speaker test confirms that your system still sounds right. More checks for speakers and recordings are in the audio test tools, and the mains hum finder stays the fastest way to see whether any hum is left.
FAQ
What causes 60 Hz hum?
Usually a ground loop: two devices are earthed through different paths, so a tiny current flows in the audio cable.
Why 50 Hz in some countries and 60 Hz in others?
It follows the mains frequency: 60 Hz in the Americas and parts of Asia, 50 Hz in most other places.
Does a ground loop isolator work?
Often yes, for unbalanced RCA or 3.5 mm links. Balanced cables are the better long-term fix.
Is it safe to cut the earth pin?
No, never. It removes your protection from electric shock.
Why does my laptop hum only on the charger?
The charger creates a ground loop with your amp. Try a grounded charger, battery power or a USB isolator.