Online oscilloscope

See the wave shape of any sound, live from your mic, a file or the test generator.

Press Listen to see your sound as a wave

The browser asks to use your microphone. Your sound stays on this device.

Or drop an audio file here.

Measurements of the waveform on the screen
ChannelFrequencyPeriodPk-pkRMSCrest
CH1—————

Scale

1 unit is digital full scale (0 dBFS), the loudest a sound file can hold.

Trigger
Edge
Level

Auto draws even without a trigger. Normal waits for one. Single takes one picture and stops.

Channels and display
Channels
Two traces

A mono source has one channel (CH1).

Cursors

Drag A or B on the screen too. Δt is the time between them; 1/Δt is the frequency of a wave that repeats over that time.

Test generator

Left is CH1; the right channel runs at the chosen ratio and phase, for XY figures. Turn on Play aloud in Source to hear it.

Source

Files are read on this device only; they are never uploaded.

Export and share

CSV lists every sample on the screen. The link keeps your settings, never your sound.

Recent results
    Sound never leaves your device. Nothing is uploaded. Space listenF freezeA auto set← → time/div↑ ↓ level/divS PNG

    How to use the oscilloscope

    1. Press Listen and allow the microphone. No mic? Choose Audio file or Test generator as the source, or Tab audio on a computer.
    2. Turn the Time/div knob until two to five waves fit across the screen, and the Level/div knob until the wave fills about half the height. Or press Auto set and let the tool pick both.
    3. Leave the trigger on Auto. If the wave drifts sideways, move Trigger level onto it. Use Normal to wait for a sound, or Single to catch one moment and stop.
    4. Read Frequency, Period, Pk-pk, RMS and Crest under the screen. Press Cursors to measure the time between any two points.
    5. Press Freeze to hold the picture, then save it as PNG or CSV. A stereo source shows two traces; press XY to draw left against right.

    How to read a waveform

    1 period = 1 ms Peak-to-peak Trigger point Trigger level −0.501234.5 msTime/div 0.5 ms · Level/div 0.1 · one square = one division
    A 1,000 Hz sine on the scope: two divisions per wave at 0.5 ms/div.

    Time per division

    The screen has 10 squares across, called divisions. Time/div says how long one square lasts. At 1 ms/div the whole screen shows 10 ms of sound: ten waves of a 1,000 Hz tone, or 4.4 waves of the note A at 440 Hz. Turn it down to see the shape of a single wave, or up to watch a whole word or a drum hit.

    Amplitude

    Up and down is the signal level, with zero in the middle of the 8 squares. Level/div sets what one square is worth, in units where 1 means digital full scale, the loudest a sound file can hold. A wave that hits 1.0 and stays flat there is clipping. Pk-pk is the height from the lowest point to the highest. RMS is the average power level, 0.707 of the peak for a pure sine.

    Trigger keeps it still

    Sound moves fast, so without help the wave would slide past in a blur. The trigger waits until the signal crosses a set level in a set direction, for example zero going up, and starts every sweep there. A repeating wave then stands still. The marker on the left edge shows the level, and the one at the top shows the trigger point, one division in from the left.

    Use cases

    See a pure tone vs a clipped one

    Choose the test generator and switch the wave from Sine to Clipped sine. A clean sine is round at the top and bottom, with a crest factor of 1.41. The clipped one has flat tops and a crest factor near 1.1, and those flat tops are the harsh sound of distortion. To find clipping in your own file, choose Normal, set the trigger level to 0.8 and play it: the scope only fires on the loudest peaks, so every flat top waits on screen.

    Measure a frequency with cursors

    The Frequency reading counts how often the wave crosses its middle level over the last quarter of a second, so a 1 kHz test tone reads 1000.0 Hz. For one odd wave or a sound that changes, press Cursors and drag A and B onto two peaks next to each other. The tool shows the time between them, Δt, and 1/Δt: a Δt of 2.273 ms means 440 Hz, the note A.

    Lissajous patterns in XY mode

    In XY mode the left channel moves the dot sideways and the right channel moves it up and down. Two equal tones in step draw a straight line; a quarter wave apart they draw a circle. Set the generator’s right channel to 2:3 and the figure gets loops in the ratio of the two frequencies. A stereo file that is really mono draws a thin rising line, and one channel wired the wrong way round flips it to a falling line.

    Class demos

    A scope makes sound visible to a whole class. Whistle and the wave is almost a pure sine; sing “aah” and it turns into a repeating pattern of bumps; a guitar string fades away slowly. Pupils can measure the period of their own voice with the cursors and work out the pitch: 5 ms means 200 Hz. On a projector, the dark screen gives the best contrast.

    Limits of a sound-card scope

    A phone or laptop only sees what its audio input hears. That is about 20 Hz to 20 kHz at best, and often less: phone mics fall off below about 50 Hz, and the sample rate, usually 48 kHz, puts a hard top limit at half of it. Most audio inputs block DC, so a steady voltage reads as zero and a slow square wave sags after each step.

    The levels are digital units, not volts. 1.0 is the full scale of the converter, and the voltage behind it depends on your device’s input gain, which the browser cannot know. Treat the numbers as relative unless you calibrate the input yourself.

    Safety: never connect mains power, a car ignition coil, a screen backlight or any circuit you do not fully understand to a mic or line input. The input is not isolated or protected, and those voltages can destroy your computer and hurt you. Even a low-voltage circuit needs a proper probe or an audio interface with input protection.

    Need a real scope?

    For electronics work, such as checking a power supply, a PWM signal or a microcontroller pin, you need an oscilloscope with real probes. A four-channel bench scope like the Rigol DS1054Z covers DC to 50 MHz, shows true volts and is a common first choice for a hobby lab. For quick checks away from the bench, a FNIRSI handheld oscilloscope runs on a battery and fits in a toolbox.

    We may earn a commission if you buy through these links. It does not change the price.

    For sound, this page is enough. To see which tones a sound is made of rather than its shape, open the spectrum analyzer, or the spectrogram to follow them over time. The guide oscilloscope vs spectrum analyzer explains when to use each, and how waves add up shows how simple sine waves build every other shape. There are more audio analyzers in the same group.

    FAQ

    Can a phone be an oscilloscope?

    For sound, yes: it shows the waveform the mic hears. It cannot measure voltages in circuits.

    What does the trigger do?

    It starts each sweep at the same point of the wave, so a repeating signal stands still on screen.

    Can I connect a circuit to the mic input?

    Not safely without a proper probe and protection. Never connect mains or high voltages. Use a real oscilloscope for circuits.

    What is XY mode?

    It plots the left channel against the right channel. Equal tones make lines or circles; different ratios draw Lissajous figures.

    Written and tested by the SpectrumAnalyzer.app team · Last checked

    How we tested: Checked with the site's own test files: the 1 kHz sine at -6 dBFS reads 1000.0 Hz, 1.000 ms, 1.000 peak-to-peak, RMS 0.354 and crest factor 1.41; the clipped-sine bursts are caught in Normal mode at a 0.8 trigger level; the out-of-phase stereo file draws a falling line in XY mode.