Buying guide
Best spectrum analyzers for every budget
The best spectrum analyzer is the cheapest one that covers the frequencies you care about. For sound, that is often free: your phone or laptop and a browser. For radio, a small handheld or a USB receiver now does what once needed a bench instrument. This guide walks through each budget, says plainly what each kind of analyzer can and cannot do, and names the products worth a look.
We may earn a commission if you buy through these links. It does not change the price.
Try it first
Working with sound? You may not need to buy anything. Our free online spectrum analyzer uses your mic, a file or tab audio and runs in your browser.
First: audio or radio?
"Spectrum analyzer" means two quite different things, and buying the wrong kind is the most common mistake.
An audio spectrum analyzer looks at sound, from about 20 Hz to 20 kHz. Its input is a microphone or a line signal, and its job is to show pitch, hum, harmonics, noise and how balanced a room or a mix is. Almost all of this can be done in software, because every computer and phone already has a sound input that covers this range.
An RF spectrum analyzer looks at radio signals, from a few kHz up to many GHz. Its input is an antenna or a cable, and its job is to show which channels are busy, how strong a transmitter is, and where interference comes from. A sound card cannot do this at all: radio is thousands to millions of times higher in frequency than sound, so you need dedicated hardware.
If you only want to look at sound, skip straight to the free section and the measurement mic section. If you work with radio, drones, Wi-Fi, remotes, ham bands or electronics that give off noise, the hardware sections are for you. And if you are not sure what a spectrum analyzer shows at all, start with what is a spectrum analyzer.
Free: online analyzer and apps
For audio, start free. The free online spectrum analyzer on this site shows every frequency from your mic, an audio file or a browser tab, with a live graph, a spectrogram, a real-time analyzer with octave bands, a hum finder and exports. Nothing is installed, and the sound never leaves your device.
Phone and desktop apps do the same kind of job. When you compare free options, look for:
- A choice of FFT size. Bigger sizes give finer detail in the bass, which matters for hum and room modes.
- Averaging and peak hold. Without them, the graph jumps too much to read.
- Octave or 1/3-octave bands. This view is the one used for room and speaker tuning.
- A way to switch off voice processing. Phones clean up sound for calls. That is good for talking and bad for measuring, because it changes the levels you see.
- Export. A picture or a CSV file lets you compare before and after.
The weak spot of any free setup is the microphone. Built-in mics are made for voices, so their bass and treble readings are not exact. For "is there hum?" or "which note is this?" that does not matter. For tuning speakers by a few dB, it does, and that is where a measurement mic comes in, further down.
Under $100: RTL-SDR kit
An RTL-SDR is a small USB radio receiver, first made from TV tuner chips, that hands the raw radio signal to your computer. With free software it becomes a live spectrum and waterfall display, and it can also listen to and decode many signals: FM radio, aircraft, weather satellites, sensors and more. It is the cheapest way to see radio at all.
The RTL-SDR Blog V4 is the current version from the team that has done the most to document these receivers. Its maker lists a tuning range from about 500 kHz to about 1.7 GHz, with the short-wave bands covered by a built-in converter, so no extra box is needed for HF.
Know the limits before you buy. An RTL-SDR shows only about 2.4 MHz of spectrum at a time. To look at a wider band, software has to step across it piece by piece, which is slow. Its levels are not calibrated, so it tells you that a signal is there and roughly how strong it is compared with others, but not its exact power in dBm. And strong nearby signals can overload it and create false signals that are not really on the air. For learning, listening and finding things, none of that gets in the way. For exact measurements it does.
RTL-SDR Blog V4
A USB radio receiver kit that turns a computer into a live spectrum and waterfall display, and decodes signals too. The best first step into radio for little money.
We may earn a commission if you buy through these links. It does not change the price.
You can plug one into our RTL-SDR in your browser page and see a live spectrum in Chrome or Edge, with no software to install.
$100–200: tinySA and tinySA Ultra
The tinySA is a real handheld spectrum analyzer: a pocket-sized box with a screen, a battery and an SMA input. It sweeps across a band by itself and shows calibrated levels in dBm, so it answers "how strong is this signal?" and not only "is something there?". It also has a built-in signal generator output, which is handy for testing filters and receivers. It is made by a small team and sold under the tinySA name; buy from a listing that names the official maker, because copies with poorer parts are common.
There are two main models. The basic tinySA is the smaller and cheaper one. Its maker lists two inputs: a low input up to about 350 MHz and a high input up to about 960 MHz. That covers FM broadcast, the 433 and 868 MHz bands used by remotes and sensors, and much of what hobbyists look at below 1 GHz.
The tinySA Ultra has a larger touch screen and goes further. Its normal range reaches about 800 MHz, and an extended "ultra" mode reaches about 6 GHz, which takes in the 2.4 and 5 GHz Wi-Fi bands, with lower accuracy and sensitivity in that mode. For most people who want one cheap analyzer that does a bit of everything, the Ultra is the pick.
Both models connect to a computer over USB for saving traces and remote control. Like every analyzer, the input can be damaged by too much power, so never connect a transmitter directly: check the maximum input in the manual and use an attenuator.
tinySA Ultra
A handheld spectrum analyzer with a touch screen, up to about 6 GHz in its extended mode. The best value for most radio hobbyists.
We may earn a commission if you buy through these links. It does not change the price.
tinySA (basic)
The smaller, cheaper model, up to about 960 MHz. Enough if your work stays below 1 GHz.
We may earn a commission if you buy through these links. It does not change the price.
New to these handhelds? Our tinySA guide covers the first settings, markers and saving traces.
Bench analyzers
A bench spectrum analyzer is a full-size instrument for a lab or a serious hobby bench. Compared with a handheld, you get a much lower noise floor, a wide choice of resolution bandwidths, steadier calibrated levels, a big screen, many markers and measurement modes, and network control. You pay for all of that: bench analyzers are a big step up in price, usually into four figures.
The Siglent SSA3021X Plus is a common entry point to this class. Its maker lists a range from 9 kHz to 2.1 GHz, resolution bandwidths down to 1 Hz and a built-in preamplifier for weak signals. That makes it a good fit for EMC pre-checks, filter and amplifier work, and radio repair below about 2 GHz. If you need higher frequencies, look at the larger models in the same family, which cost more.
Buy a bench analyzer when a handheld's limits are in your way every week: when you need to see very weak signals next to strong ones, compare products against a limit line, or log measurements over many hours. Otherwise, a handheld does most hobby jobs.
Siglent SSA3021X Plus
A bench spectrum analyzer from 9 kHz to 2.1 GHz with a low noise floor and fine resolution bandwidth. A sound first lab instrument.
We may earn a commission if you buy through these links. It does not change the price.
Audio: measurement mic + this site
For sound, the best upgrade is not an analyzer at all: it is a better microphone. A measurement mic is built to hear every frequency at the same level, so the graph shows the sound and not the mic. Pair it with the free tools here and you have a setup that is good enough for tuning a room, setting up speakers or checking a PA.
The easiest kind plugs straight into USB and needs no audio interface. The miniDSP UMIK-1 is a popular one: it comes with a calibration file made for its own serial number, which corrects the small errors left in the mic. It works in the browser like any other mic. Open the real-time analyzer or the spectrum analyzer, choose it as the input, and you are measuring.
miniDSP UMIK-1
A USB measurement microphone with its own calibration file. Plug it in, pick it in the browser and measure rooms and speakers properly.
We may earn a commission if you buy through these links. It does not change the price.
If you already own an audio interface, an XLR measurement mic is another good route.
Comparison table
Rough guide only. Ranges are from the makers' own specifications, and price bands are approximate and change often, so check the current price before you buy.
| Option | Range | Span at once | Price band | Best for |
|---|---|---|---|---|
| Online analyzer (this site) | Sound, about 20 Hz–20 kHz | Whole audio range | Free | Hum, pitch, mixes, rooms |
| RTL-SDR Blog V4 | About 500 kHz–1.7 GHz | About 2.4 MHz | Under $100 | Learning radio, listening, decoding |
| tinySA (basic) | About 100 kHz–960 MHz | Any span in range (sweeps) | About $100 or less | Bands under 1 GHz on a budget |
| tinySA Ultra | About 100 kHz–6 GHz (extended mode) | Any span in range (sweeps) | $100–200 | One cheap analyzer for most hobby work |
| Siglent SSA3021X Plus | 9 kHz–2.1 GHz | Any span in range (sweeps) | Four figures | Lab work, EMC pre-checks, weak signals |
| miniDSP UMIK-1 + this site | Sound, about 20 Hz–20 kHz | Whole audio range | Under $200 | Room and speaker tuning |
How we chose
We have not lab-tested these products, and we will not pretend to: there are no star ratings or test scores on this page that we did not measure. We picked each one because it is the clear, widely used choice in its class, and we describe it from the maker's published specifications and from what that class of analyzer can and cannot do. Where a product has a limit that buyers often miss, such as the RTL-SDR's narrow view or the tinySA Ultra's lower accuracy in its extended mode, we say so. We will update this page when the line-ups change.
FAQ
What is the best cheap spectrum analyzer?
The tinySA Ultra, for most hobbyists. It covers a wide range, up to about 6 GHz in its extended mode, and it is simple to use, for well under bench prices.
Is an RTL-SDR a spectrum analyzer?
A limited one. It shows about 2.4 MHz of spectrum at a time and its levels are not calibrated, but it can also decode signals, and it is very cheap.
Do I need a hardware analyzer for audio?
No. A computer or phone with a good mic and this site's free tools covers audio. A hardware RF analyzer cannot hear sound at all.
What should a beginner look for?
A frequency range that covers your bands, a low noise floor, easy markers and a way to save traces.