Speaker & audio tests
Speaker and audio test tools
These tests play a sound from your speaker and listen with your microphone, so you can check a speaker, a subwoofer, an amp or a Bluetooth link without buying a measuring rig. Everything runs in your browser and no sound is uploaded. For a room’s reverb and bass modes, see the room acoustics tools.
- Frequency Response TestPlay a sweep through your speakers and measure their response with a mic.
- THD / Distortion AnalyzerMeasure THD, THD+N and each harmonic of a test tone in % and dB.
- Resonance Frequency FinderTap an object and find the frequencies it rings at, with the Q factor.
- Speaker Polarity TestCheck if each speaker is wired in phase or the wrong way round.
- Audio Latency TestMeasure the delay of Bluetooth headphones, speakers or an audio interface.
- How to Fix Mains HumWhy speakers hum or buzz at 50 or 60 Hz, and safe fixes for ground loops.
- Best Measurement Microphone SoonUSB or XLR, calibration files and phone mics: which measurement mic fits your budget.
Which test do I need?
Start with the question you want answered, then pick the test that measures it.
- “Does my speaker sound even, or is the bass boomy?” Use the frequency response test. It plays a sweep from 20 Hz to 20 kHz and draws how loud each frequency comes back at your seat, with up to 4 curves to compare spots or speakers.
- “Is my amp or interface clean?” Use the THD analyzer. It plays a pure 1 kHz or 100 Hz tone and measures the harmonics the gear adds, in % and dB.
- “Is one speaker wired the wrong way round?” The speaker polarity test plays a pulse and tells you if each speaker pushes or pulls first.
- “Why is the sound late on my Bluetooth headphones?” The audio latency test measures the delay in milliseconds.
- “What note does this glass, bell or guitar top ring at?” Tap it and use the resonance frequency finder.
- “My speakers hum.” Read how to fix mains hum, which finds the 50 or 60 Hz hum with the live analyzer and walks through safe fixes.
Most people start with the frequency response test, because it shows both the speaker and the room in one picture. If the curve looks odd only in one channel, check the polarity next.
What a phone mic can and cannot measure
A phone or laptop mic is better than many people expect. It hears clearly from about 80 Hz to 12 kHz, its timing is exact, and the tests that compare two things, such as before and after, left and right, or one seat and another, work well with it. Polarity, delay and resonance tests only need timing or pitch, so a phone mic is fine for them.
It has two weak spots. Most phone mics lose level below about 50 Hz, so the deep bass of a subwoofer reads lower than it really is. Many also lift the range from 2 to 5 kHz a little to make voices clearer, and some phones still run noise suppression or automatic gain. Our tools ask the browser to switch both off, and show a badge when the browser says it could not.
A USB measurement microphone fixes both weak spots. It comes with a calibration file, a list of small corrections for its own serial number, which the frequency response test can load and remove from every curve.
miniDSP UMIK-1
A USB measurement microphone that comes with a calibration file for its serial number. It shows up as a normal microphone in the browser.
We may earn a commission if you buy through these links. It does not change the price.
For the THD test, the most exact result comes from a loopback cable from the output straight back to the input, which leaves the mic and the speaker out of the chain.
Safe test volumes
Test tones and sweeps carry more energy than music at the same volume setting, so start with the volume low and raise it slowly. The sweep fades in, and the tools warn you when the test level is set high. Small speakers and laptop speakers can be damaged by loud deep bass, and tweeters by loud high tones. Protect your ears too: if the test sounds uncomfortable, it is too loud for a good measurement anyway.
FAQ
Can I test speakers with my phone?
Yes, for frequency response, polarity and delay. For exact low-bass levels a USB measurement mic is better.
Do I need special cables?
Only the THD test needs a loopback cable for the most accurate result; all other tests use the speaker and mic.
Is a sweep test safe for speakers?
Yes at normal listening volume. Start low, the sweep fades in, and never push small speakers hard in the deep bass.
Why does my result change when I move the mic?
Rooms add reflections and bass build-up. Measure at the listening spot and average a few positions.