Speaker and room frequency response test
Play a sweep through your speaker, record it with the mic and see the real frequency response curve.
Press Measure to play the sweep
Turn the volume low first. The sweep plays from your speaker while the mic records; it stays on this device.
Or drop a recording of the sweep, or a mic calibration file, here.
Sweep
This is loud. Turn your speaker down first and raise it slowly. Never push small speakers hard in the deep bass.
The sweep starts softly at 20 Hz and rises to 20 kHz. Bluetooth delay does not matter: it is found and removed.
Measurements
Display
Mic calibration
Measurement mics such as the UMIK-1 come with a .txt or .cal file of “frequency dB” lines. It is read on this device and kept for your next visit.
Source
To test a TV or hi-fi, save the sweep, play it there and record it with a phone, then open the recording here. The mic turns off after each sweep.
Export and share
CSV holds every shown curve at 1/48-octave steps. The link keeps your settings, never your sound.
Recent results
How to use the frequency response test
- Put the phone or laptop where you sit, at ear height, with nothing between it and the speaker. For one speaker on its own, measure close up instead: about 30 to 50 cm in front of the tweeter.
- Turn the volume low, then press Measure and allow the microphone. The sweep is a rising tone from deep bass to high treble; raise the volume until it sounds clearly louder than the room, but never harsh.
- Stay quiet while it plays. Two to three seconds later the curve appears. If the badge says Quiet, raise the volume a little; if it says Clipped, turn it down.
- Measure again from other spots, or the left and right speaker on their own. Up to 4 curves are shown together, and you can rename each one.
A 5-second sweep at −20 dBFS suits most rooms. Choose 10 seconds in a noisy room, because a longer sweep rises further above the background. To test a TV or a hi-fi that the browser cannot play to, press Save the sweep as WAV, play the file there, record it with a phone and open the recording here.
How to read the curve
The chart shows how loud each frequency comes back compared with the rest. 0 dB is the average from 500 Hz to 2 kHz, where speakers are usually at their most even, so a perfect system would draw a flat line at 0 dB from 20 Hz to 20 kHz. Lines above 0 dB are too loud, lines below are too quiet.
±3 dB
The green band marks ±3 dB, a 3 dB step being about the smallest change most people notice in music. The readout gives the widest range that stays inside it: “48 Hz–17.4 kHz” is a good result for a bookshelf speaker. Flatness gives half the gap between the highest and lowest point from 100 Hz to 10 kHz, so ±2 dB is very even and ±8 dB sounds coloured.
Bass bumps and dips
Below about 300 Hz, the room takes over. Bass waves bounce between the walls and add up or cancel, so a seat can get +8 dB at 46 Hz and −10 dB at 120 Hz from the same speaker. A narrow dip that moves when you move the mic by 50 cm is the room; a slope that stays put is the speaker.
Smoothing
A raw curve is full of tiny spikes from echoes. Smoothing averages each point over part of an octave: 1/3 octave shows the overall tone balance, 1/6 is a good everyday view and 1/24 shows the exact shape of a room mode before you set an EQ filter. The status line names the biggest bump and dip.
Use cases
Speaker placement
Measure each speaker on its own from the listening seat, then move it 20 cm further from the wall and measure again. Moving a speaker away from the wall behind it often fills a dip between 80 and 200 Hz by 5 dB or more. Keep the position with the smoothest curve.
Subwoofer crossover check
Play the sweep through the speakers and the subwoofer together and look at the 60 to 120 Hz area. A deep, narrow hole at the crossover, for example −12 dB at 80 Hz, usually means the sub and the speakers cancel. Flip the sub's phase switch or change its delay, measure again and keep the setting with the fuller curve. A polarity test checks the wiring first.
Before and after room treatment
Measure at the seat with the whole response, then add bass traps or move the sofa and measure again. Each result is kept under Recent results; press Compare to draw the old curve as a dotted line. A good change can turn a +9 dB peak at 50 Hz into +4 dB.
DIY speaker build
Measure the new speaker close up, 50 cm in front of the tweeter, and set the window to 5 ms. That cuts off the echoes from the floor and walls, which arrive a few milliseconds later, and leaves the speaker's own response above about 200 Hz. Look for a smooth crossover region near 2 to 3 kHz, then use the distortion test to see how cleanly it plays loud.
Tips for accurate results
Gating. The window keeps only the first part of the impulse response. Short windows remove reflections, but they also blur the bass: a window of 5 ms is only reliable above about 200 Hz, and the chart shades the area below. Use the whole response, or 300 ms, for room and bass work, and 3 to 10 ms for a speaker on its own.
Calibration file. Phone and laptop mics are made for voices. Most lose level below about 50 Hz and many add a small lift between 2 and 5 kHz, so trust changes between curves more than the exact shape at the ends. Measurement mics come with a calibration file for their serial number, which this tool loads under Mic calibration and removes from every curve. See our guide to measurement microphones for the options.
Keep the room quiet, switch off fans, and hold still. If a phone plays the sweep very quietly while the mic is on, it may have moved the sound to its earpiece: connect the speaker you want to test by cable or Bluetooth.
miniDSP UMIK-1
A USB measurement microphone with a calibration file for its serial number. Pick it as the microphone in the browser and load its file here.
We may earn a commission if you buy through these links. It does not change the price.
How the sweep method works
The sweep is an exponential sine sweep: it spends the same time in every octave, from 20 Hz to 20 kHz. The tool knows exactly what it played, so it divides the recording by the sweep in the frequency domain. This is Angelo Farina's method, and what comes out is the impulse response: how your speaker and room answer one short click. Its main peak sets the delay, so Bluetooth latency does not matter, and distortion from the speaker lands before that peak, where the window leaves it out. The window is then applied and the frequency response is computed from what is left. For a live view of bands while you adjust an EQ, use the RTA with pink noise. More tests are in the speaker and audio test tools.
FAQ
What is a good frequency response?
Within ±3 dB across the range you care about is good for speakers; rooms add bigger bass swings, often ±10 dB.
Why use a sweep instead of noise?
A sweep separates the speaker's sound from echoes and distortion, giving a cleaner curve.
Can I measure headphones?
Not reliably without a proper ear coupler; this tool is for speakers and rooms.
Do I need a calibrated mic?
For the trend, no. For exact bass and treble levels, import a calibration file from a measurement mic.