RF tools · Guide

How to use the tinySA spectrum analyzer

The tinySA is a pocket spectrum analyzer that costs about as much as a good multimeter. It shows radio signals as peaks on a screen, from the FM band to WiFi, and it can save what it sees as a CSV file. This guide takes you from the box to your first useful measurement: which model to pick, how to set it up, what span, RBW and markers mean, how not to burn the input, and how to save and share traces.

This guide has links to products. We may earn a commission if you buy through these links. It does not change the price.

Try it

Already saved a trace? Open it in the RF trace viewer to add markers, list the peaks, compare two scans and check a limit line. The file stays on your device.

tinySA vs tinySA Ultra: which to buy

There are two main models. Both are small battery-powered boxes with a screen and SMA sockets, and both are made by the same designer, but they are built for different ranges.

The tinySA (the first, smaller model) has two inputs. The LOW input covers about 100 kHz to 350 MHz with the best accuracy, and the HIGH input covers about 240 to 960 MHz. That is enough for the FM band, airband, 2 m and 70 cm ham bands, 433 and 868 MHz remotes and most ISM devices below 1 GHz.

The tinySA Ultra has a bigger touch screen, a single input that works best up to about 800 MHz, and an "Ultra" mode that reaches about 6 GHz with lower accuracy. That adds the 2.4 and 5 GHz WiFi bands, Bluetooth, drones and many radar sensors. It also has a built-in preamp for weak signals and a slot for a memory card.

tinySA Ultra

The pick for most people: it covers WiFi and other gigahertz signals, the screen is easier to read, and the preamp helps with weak signals.

Check price on Amazon

We may earn a commission if you buy through these links. It does not change the price.

tinySA (basic)

Cheaper and smaller. Enough if everything you care about is below 1 GHz, such as FM radio, ham radio or 433 MHz remotes.

Check price on Amazon

We may earn a commission if you buy through these links. It does not change the price.

Both are popular, so copies with older firmware or poor parts are sold too. Buy from a seller that names the official version and check the serial number and firmware screen when it arrives. For other choices, including bench analyzers, see the best spectrum analyzers.

First setup: firmware, calibration and self-test

Charge the battery fully first; a low battery can give odd readings. Then switch on and open the version screen in the CONFIG menu to see which firmware you have.

Firmware. New firmware fixes bugs and often adds features. The official site, tinysa.org, has the latest file and the steps. The usual way is to start the tinySA in its update mode (on most units you hold the jog switch down while switching it on) and send the file from a PC with the update tool the site names. Do not unplug the cable while it writes. If you are not sure, it is fine to skip this step at first: a tinySA works well with the firmware it came with.

Self-test. The tinySA has a built-in test signal. Connect the short cable that came in the box from the calibration output to the input (on the basic model, CAL to LOW) and run the self-test from the CONFIG menu. Every line should say pass. A failure usually means a loose cable or the wrong socket, so check those before anything else.

Level calibration. With the same cable in place, the level calibration step uses the internal 30 MHz signal to correct the level readings. Run it once when the unit is new and again after a firmware update. After that, the tinySA reads levels to within a couple of dB, which is plenty for hobby work.

Last, connect an antenna. The short telescopic antenna that often comes with it is fine for the FM band and above; for HF you need a longer wire.

Your first measurement

A spectrum analyzer draws a graph: frequency from left to right and signal level from bottom to top. Every station or device that is on the air shows as a peak. Five settings decide what you see.

Centre and span

The centre is the frequency in the middle of the screen, and the span is how wide the screen is. To look at the FM band, set start 88 MHz and stop 108 MHz (or centre 98 MHz and span 20 MHz). Each FM station then shows as a peak about 200 kHz wide. To look at one 433.92 MHz remote, set the centre to 433.92 MHz and the span to 1 MHz, then press the button on the remote: a peak jumps up while it sends.

RBW (resolution bandwidth)

The RBW is the width of the filter the tinySA sweeps across the band. A narrow RBW separates two close signals and lowers the noise floor, so weak signals stand out more. The price is time: a sweep gets about 100 times slower when the RBW is 10 times narrower. Leave it on auto at first; the tinySA picks an RBW that suits the span. Narrow it by hand when two peaks merge into one or a weak signal hides in the noise. Every 10 times narrower RBW lowers the noise floor by 10 dB; our noise floor and RBW calculator shows the numbers for your settings.

Reference level and attenuation

The reference level is the level at the top line of the screen. If a peak is cut off at the top, raise it; if everything is squeezed at the bottom, lower it. Changing it only moves the picture. The input attenuation is different: it really weakens the signal before the mixer. Leave it on auto. Add attenuation when a strong signal makes extra peaks appear (a sign of overload): if a peak drops by exactly as many dB as you added, it is real; if it drops more or disappears, it was made inside the tinySA.

Markers

A marker reads the exact frequency and level of one point. Turn on marker 1 and use "peak search" to put it on the highest peak: the readout shows, for example, 94.500 MHz at −38 dBm. Add a second marker and set it as a delta marker to read the distance between two peaks, for example how much weaker a harmonic is than the main signal. Max hold, in the trace menu, keeps the highest level at each frequency, which is the easy way to catch a device that only sends short bursts.

A good first exercise: scan 88 to 108 MHz, put marker 1 on the strongest station and write down its level. Then move the antenna or go to another room and compare. You have just made your first coverage test.

Don't burn the input

The input of a tinySA is sensitive, and that is why it can see weak signals. It also means a strong signal can damage it in a fraction of a second. Keep the input below about +10 dBm (10 milliwatts), and check your model's manual for its exact limit and for the DC voltage it can take.

That rules out connecting a transmitter directly. A 5 W handheld radio puts out about +37 dBm, more than 500 times too much. Always put an attenuator between a transmitter and the tinySA: a 30 dB power attenuator brings 5 W down to +7 dBm, and a 40 dB one gives you more margin. Make sure the attenuator is rated for the power. A DC block protects the input from voltage on the line, for example when you test an antenna with a powered amplifier. And if you measure near a strong transmitter with an antenna, start with extra attenuation and remove it step by step.

The tinySA can also send a test signal from its output. Only connect that output to the device you test, never to an antenna, because transmitting outside the licence-free bands is not allowed.

Save and share traces

The screen is fine for a quick look, but a saved trace is better for reports, forum posts and before/after comparisons. There are two ways to save one.

  1. With a PC program. Connect the tinySA by USB and open tinySA-App (Windows) or QtTinySA (Windows, macOS and Linux). Both show the live trace on the PC and can save it as a CSV file: each line holds a frequency and a level.
  2. On the device. The Ultra can save screenshots and traces to its memory card from the storage menu. Copy the files to your computer afterwards.

Then open the file in our trace viewer to view tinySA CSV files. It finds the columns on its own, puts a marker on the highest peak, lists the top 10 peaks and can show up to 4 traces at once, so you can compare two antennas or a before and after. A limit line marks every point above a level you choose, and the PNG export gives a clean picture to post. If a file is read wrongly, the column picker lets you set which column is which.

Name your files with the date and what you measured, for example "2026-11-22 FM band roof antenna.csv". Six months later you will be glad you did.

tinySA vs RTL-SDR vs bench analyzer

tinySA / UltraRTL-SDR dongleBench analyzer
What it isA swept spectrum analyzerA USB radio receiverA calibrated lab instrument
Seen at onceAny span in one sweepAbout 2.4 MHz liveAny span, fast sweeps
Level readingsIn dBm, within a few dBRelative onlyIn dBm, within about 1 dB
Decodes signalsNoYes (with software)Some models
Needs a PCNoYesNo

The tinySA is the right tool when you want to see a whole band and read real levels, for example to find which frequency a device uses or whether a filter works. An RTL-SDR is better when you want to listen to or decode what you found, and it is cheaper, but it only shows a narrow slice at a time and its levels are not calibrated. A bench analyzer from a maker such as Siglent or Rigol is faster, more accurate and has a lower noise floor, and it is what you need for real compliance work, at ten or more times the price. Many hobbyists end up with a tinySA and an RTL-SDR side by side. All our RF tools are on the RF tools page.

FAQ

Is the tinySA any good?

For hobby and learning, yes: it is small, cheap and covers up to about 6 GHz (Ultra). It is not a calibrated lab analyzer.

What is the maximum input of a tinySA?

Keep it below about +10 dBm; use an attenuator for transmitters. Check your model's manual.

tinySA or RTL-SDR?

The tinySA is a true spectrum analyzer with wide sweeps; an RTL-SDR shows 2.4 MHz at a time but can decode signals.

How do I export CSV?

With the PC software (tinySA-App or QtTinySA) save the trace as CSV, then open it in our trace viewer.

Written and tested by the SpectrumAnalyzer.app team · Last checked

How we tested: The "Open a tinySA CSV" button opens the RF trace viewer, which was checked with the site's tinySA sample trace: peaks at 94.500, 101.100 and 105.300 MHz read −38, −45 and −52 dBm.