Real time analyzer (1/3-octave RTA)

See your sound in 1/3-octave bands, with pink noise built in, to tune a room or a speaker.

Press Listen, then play pink noise

The browser asks to use your microphone. Your sound stays on this device.

Or drop an audio file here.

Average—
Spread—
Loudest—

Pink noise

It fades in over 3 seconds and plays from this device's speakers or the speaker it is connected to. Bluetooth delay does not matter here: an RTA measures the steady sound, not timing.

Display
View
Averaging
Weighting
Target curve
House: a gentle fall of 1 dB per octave toward the treble.
Calibration
Added to every band. With a sound level meter: if it reads 85 dB SPL while a band average here reads −20 dB, enter 105 to read dB SPL.
Band table
Band (Hz)Level (dBFS)vs average
Stored curves
    Source

    Files are read on this device only; they are never uploaded.

    Export and share

    CSV holds every band with its level, deviation and stored curves. The link keeps your settings, never your sound.

    Recent results
      Sound never leaves your device. Nothing is uploaded. Space listenN pink noiseF freezeR resetS store

      How to use the RTA

      1. Put the phone or laptop where you sit to listen, with the mic pointing up at ear height. Keep it away from walls and your body.
      2. Press Listen and allow the microphone. No mic? Choose Demo room or Audio file as the source.
      3. Turn your amplifier or speaker down, then press Pink noise. It fades in over 3 seconds. Raise the volume until the bars sit well above the room noise, about the level of loud talking.
      4. Leave Averaging on Slow and wait a few seconds. Read the bars: tall bars are bands that are too loud and short bars are too soft.
      5. Press Store curve to keep the result as line A. Change one thing, such as an EQ band or the speaker position, and store it again as B to compare.

      Use Reset to start a new average, and CSV in the band table to save every band as a file. For a quick look at the whole room rather than one seat, choose Infinite averaging and walk the phone slowly around the listening area for 20 to 30 seconds. The bars then show the room average, which is a better guide for EQ than one spot.

      How to read the bars

      Peak: room mode at 63 Hz Dip near 2.5 kHz House curve (target) Microll-off +100−10−2031.51255002k8kBand centre in Hz · level in dB against the average (0)
      A room with a boomy mode and a dip, measured with pink noise. The dashed line is the house-curve target.

      Each bar is one band. In the 1/3-octave view there are 31 bands, from 20 Hz on the left to 20 kHz on the right, on the standard ISO centre frequencies such as 63, 125, 1,000 and 8,000 Hz. The height is the level in that band. The readouts under the graph give the average from 50 Hz to 16 kHz, the spread (how far the bars stray from the average or the target, plus or minus) and the loudest band.

      Flat is the goal, not always best

      Pink noise has equal energy in every octave, so a perfect speaker in a perfect room shows level bars. Real rooms that measure dead flat at the seat often sound thin and bright, because walls and furniture soak up more treble than bass. Turn on the House target to see a gentle line that falls 1 dB per octave, and aim for bars that follow it within about ±3 dB.

      Peaks vs dips

      A peak, such as a bar 8 dB above the rest at 63 Hz, is easy to fix: cut that band with EQ. A deep dip is different. It is often sound from a wall arriving out of step and cancelling the direct sound, and boosting it only wastes amplifier power. Move the speaker or the seat instead and watch the dip change.

      Averaging

      Noise is random, so bars jump from moment to moment. Fast averaging (125 ms) follows music, slow (1 s) gives steady bars for EQ work, and infinite keeps one running average until you press Reset.

      Use cases

      EQ a PA system

      Before a gig, play pink noise through the PA, stand at the mix position and use slow averaging. If the 250 Hz and 315 Hz bars sit 5 dB over the rest, the sound will be muddy; cut those bands on the graphic EQ by about 4 dB and watch the bars settle. Store a curve before and after so the change is plain to see.

      Find a boomy room mode

      One bass note that booms louder than the others is usually a room mode. Play pink noise and look for a single tall bar between 30 and 120 Hz, often 6 to 12 dB above its neighbours. The demo room has one at 63 Hz. Work out where your room's modes should be with the room mode calculator.

      Set a subwoofer level

      Play pink noise through the main speakers and the subwoofer together, with slow averaging. Turn the sub up or down until the bars from 31.5 to 80 Hz line up with the bars from 100 to 400 Hz, or sit 2 to 4 dB higher if you like more bass. Then switch to the House target to check the whole curve.

      Compare speaker positions

      Measure with infinite averaging, store the curve as A, move the speakers 30 cm away from the wall, press Reset and measure again as B. Bass bars often change by 3 to 6 dB between positions. Keep the spot with the smoothest bars.

      Tips for accurate results

      Phone and laptop mics are made for voices. Most of them drop off below about 50 Hz, so the lowest bars read low even when the bass is there; the graph shades that area when the source is a microphone. Many also add a small lift around 2 to 5 kHz. Trust changes more than absolute levels: store a curve, change one thing and compare.

      Keep the room quiet, turn off fans, and play the pink noise at least 20 dB above the room noise. Hold the phone at arm's length or put it on a stand, since your body reflects sound. If the clipping badge shows, turn the volume down a little.

      For real measurements, a USB measurement mic with its own calibration file gives a flat, known response down to 20 Hz.

      miniDSP UMIK-1

      A USB measurement microphone with a calibration file for its serial number. It plugs into a laptop or a phone with an adapter and works in the browser like any other mic.

      Check price on Amazon

      We may earn a commission if you buy through these links. It does not change the price.

      RTA vs FFT spectrum

      An FFT analyzer splits sound into thousands of narrow, equally spaced lines, which is right for finding one exact tone, such as hum at 60.0 Hz. An RTA adds those lines up into bands that get wider as the frequency rises, the way we hear. Pink noise then looks flat instead of falling, and a room's balance is easy to read. For one tone, use the FFT spectrum analyzer; to see how sound changes over time, use the spectrogram. The RTA also updates the low bands more slowly than the high ones, because a narrow band at 31.5 Hz needs more time to measure than a wide band at 8 kHz. The exact edges of every band are listed in the 1/3 octave band frequencies tool.

      FAQ

      What is an RTA?

      A real time analyzer shows sound split into fixed bands, usually 31 bands of 1/3 octave, so you can see which areas are too loud or too soft.

      Why use pink noise?

      Pink noise has equal energy per octave, so a perfect system shows flat bars on an RTA.

      Should my RTA be flat?

      Most rooms sound best with a gentle fall toward the treble. Use the house-curve overlay as a guide.

      Can I use my phone as an RTA?

      Yes, from about 50 Hz up. Below that, phone mics drop off; a USB measurement mic fixes it.

      What averaging should I use?

      Slow (1 s) for EQ work, fast for watching music, and infinite to build a steady room average while you move the mic.

      Written and tested by the SpectrumAnalyzer.app team · Last checked

      How we tested: Checked with the site's own test files: pink noise reads flat within ±1 dB in every 1/3-octave band from 25 Hz to 16 kHz, white noise rises about 1 dB per band (3 dB per octave), and a 1 kHz sine at -6 dBFS reads -6.0 dB in the 1 kHz band.