RF tools
RF tools and calculators
Tools for radio work: open the CSV traces your spectrum analyzer saves, plan WiFi channels and work out the numbers every RF project needs, from dBm to path loss. Start with the RF trace viewer, which plots tinySA, Rigol, Siglent and rtl_power files with markers and limit lines.
Viewers
- RF Spectrum Trace ViewerOpen CSV traces from a tinySA, Rigol, Siglent or RF Explorer and add markers.
- Live RF Spectrum (RTL-SDR)Plug in an RTL-SDR dongle to see a live radio spectrum and waterfall.
- WiFi Channel PlannerPlan 2.4, 5 and 6 GHz WiFi channels and see which ones overlap.
- tinySA GuideSet up a tinySA, make your first measurement and save CSV traces.
Calculators
- Noise Floor & RBW CalculatorWork out the displayed noise floor from RBW and noise figure.
- dBm ConverterConvert dBm, mW, W, dBµV and volts in one box, for 50 or 75 ohm.
- VSWR CalculatorConvert VSWR, return loss, reflection coefficient and mismatch loss.
- Path Loss & Link Budget CalculatorFree space path loss and a full link budget with fade margin.
- Noise Figure Cascade CalculatorAdd up gain and noise figure through a chain of stages (Friis).
- Harmonics & Intermodulation CalculatorList the harmonics and mixing products of two or three signals in your band.
- Phase Noise to Jitter CalculatorTurn phase noise points from a datasheet into RMS jitter.
- ENOB CalculatorConvert between ADC SNR, ENOB, SINAD and SFDR.
- Antenna Length CalculatorDipole, quarter-wave and 5/8-wave lengths for any frequency.
Audio vs RF spectrum analyzers
Both kinds of analyzer answer the same question: how strong is each frequency? The difference is the range. Sound lives between 20 Hz and 20 kHz, so a phone microphone and a sound card can sample it directly, and this site's live spectrum analyzer does the rest in the browser. Radio starts where sound stops and goes up to many gigahertz: FM broadcast sits at 88 to 108 MHz, WiFi at 2.4, 5 and 6 GHz. No sound card can sample that fast, so radio needs its own hardware.
An RF spectrum analyzer such as the tinySA sweeps a narrow filter across the band and measures the power that comes through, point by point. The width of that filter is the RBW (resolution bandwidth): a narrow RBW separates close signals and lowers the noise floor, but makes each sweep slower. An SDR dongle works more like an audio analyzer: it moves a slice of the radio band down to a low frequency, samples about 2.4 MHz of it at once and runs an FFT, the same maths as the audio tools here.
The levels are also counted differently. Audio tools show dBFS, relative to the loudest sound the input can take. RF tools show dBm, an absolute power, so a −40 dBm reading means the same on any calibrated analyzer.
A cheap RF starter kit
Two small devices cover most hobby radio work for less than the price of one hour of lab time. A handheld spectrum analyzer shows what is on the air across a wide band, and an SDR dongle lets you listen to and decode what you find.
tinySA Ultra
A pocket spectrum analyzer with a touch screen, up to about 6 GHz in its extended mode. It saves traces as CSV, which open straight in the trace viewer.
We may earn a commission if you buy through these links. It does not change the price.
RTL-SDR Blog V4
A USB radio receiver from about 500 kHz to 1.7 GHz. It shows about 2.4 MHz of spectrum at a time as a live waterfall, and rtl_power turns it into a slow wide-band scanner.
We may earn a commission if you buy through these links. It does not change the price.
Add a few SMA cables, a 20 or 30 dB attenuator to protect the inputs from nearby transmitters, and a telescopic antenna. For bench analyzers and other choices, read the hardware spectrum analyzer guide.
Units you will meet
- dBm is power compared with 1 milliwatt. Every 10 dB is ten times more power: 0 dBm is 1 mW, 20 dBm is 100 mW, −30 dBm is 1 µW and −100 dBm, a weak signal, is 0.1 picowatt.
- dBµV is voltage compared with 1 microvolt. On a 50 Ω system, 0 dBm is 107 dBµV, so −60 dBm is 47 dBµV. EMC limits are often written in dBµV.
- Ω (ohm) is the impedance. Radio gear uses 50 Ω; TV and satellite cables use 75 Ω. The same power gives a different voltage on each, which is why dBµV readings need the impedance.
How these tools work in your browser
Everything runs on your own device: trace files are read by your browser and never uploaded, and the calculators work offline once the page has loaded. The results are only as good as the input. A trace shows exactly what your analyzer measured, with its own accuracy, and a calculator uses the textbook formula, so real cables, connectors and antennas add losses that you should allow for with a few dB of margin.
FAQ
Can a browser show radio signals?
Yes, with an RTL-SDR USB dongle in Chrome or Edge. Without hardware, use the calculators and the trace viewer.
What is dBm?
Power compared with 1 milliwatt: 0 dBm = 1 mW, 30 dBm = 1 W, −30 dBm = 1 µW.
Which cheap spectrum analyzer is good for beginners?
The tinySA Ultra covers up to about 6 GHz and costs far less than a bench analyzer. See our buying guide.
Are these calculators accurate?
They use the standard formulas shown on each page. Real systems add losses, so keep a margin.